Xmotorstore Payments
Conical spacer on the crown side DM, the spacer must be inserted between the swingarm and the wheel bearing with the diameter of the narrowest cone towards the bearing. The wheel spacer Dm has the following measures:
Hole diameter 10 mm
Outside diameter 24 mm
Outside diameter narrow part 15 mm
Spacer thickness 10 mm
Dm code: 001002R002B0
Conical spacer on the crown side DM, the spacer must be inserted between the swingarm and the wheel bearing with the diameter of the narrowest cone towards the bearing. The wheel spacer Dm has the following measures:
Hole diameter 10 mm
Outside diameter 24 mm
Outside diameter narrow part 15 mm
Spacer thickness 10 mm
Dm code: 001002R002B0
Reference: 001002SP1200
Brand: DM
Rear wheel axle for steel swingarm since 2008 DM
Reference: 001002SP095D
Brand: DM
Rear wheel pin for aluminum swingarm Dm
Reference: KOYO 60002
KOYO racing minimoto wheel bearings 10x26x8, compatible with all minimoto bikes. The high-speed wheel bearings for minimoto allow you to improve the sliding of the minimoto when cornering.
Reference: GHR 031.003
Brand: GHR
Complete GHR 2-mass 80mm G-carbon-Tech clutch with adjustable G-Radius black plate. The Ghr clutch for minimoto is compatible with most of the minimoto engines on the market, such as: Bzm, Polini, Iame, Cs, Or, and others. G-Carbon-tech compound.
Reference: 017010
Brand: BZM
Bzm minimoto piston for 50cc 2t. Original Bzm piston diameter 40mm with flat head for 50cc 2t engines. Available in sizes: Piston bzm selection 0. Piston bzm selection A. Bzm piston AA selection. Piston bzm selection B. Attention: The clearance between piston and cylinder must be approximately 0.040 (four hundredths).
Reference: 143.015.023
Brand: POLINI
Polini minibike air cylinder head diameter 36mm 40cc. Polini Code: 143.015.023
Reference: 7004
Brand: STAMAS
Stamas minimoto internal steering head spacer
Reference: 228.0001
Brand: POLINI
Long exhaust muffler spring (70mm) 228.0001
Reference: 2016/28
Brand: STAMAS
Cnc support for factory hydraulic front brake caliper plus screws for 28 mm stems
Reference: 143.420.003
Brand: POLINI
Left front brake caliper lever with spring. Polini code: 143.420.003. Left front brake caliper lever with Polini spring for minibike.
Reference: 001002SP1200
Brand: DM
Rear wheel axle for steel swingarm since 2008 DM
Reference: Ariane-K2Re
Brand: Arianetech
Ariane K2Re was designed in response to the models that are the reference among the current minibikes, but in an electric version. For this reason it is equipped with an electric unit with a maximum power of 6.5 kW (8.5 HP), adjustable in multiple parameters via a USB port that connects to a laptop to adapt to the needs of every rider, from the beginner...
Reference: FRZ.HM3
Brand: CS Racing
Clutch Cs minimoto HAMMER EPIC. Clutch for minimoto compatible with Cs, Iame, Ghr, Bzm engines. This clutch must be used with an 81mm bell. Cs clutch models: - HAMMER GT Low friction coefficient, allows greater slip without affecting performance - HAMMER GP Medium-high friction coefficient - HAMMER EPIC High Coefficient
Reference: 5006
Brand: STAMAS
Front hub Stamas factory including spacer and bearings.
Reference: 112.159.11
Brand: GRC
Rear brake caliper mechanical support for short hub l.111 Grc
Reference: 215.0224
Brand: POLINI
Polini 4.2 hp engine intake manifold, external diameter 19 mm (carburetor connection), internal diameter 15 mm. The manifold is compatible with 4.2 hp and Peugeot 103 minimoto engine. Polini Code: 215.0224
Reference: 001002R003B0
Brand: DM
rubber kit for fairing Dm 5 pieces. Suitable for original fairings, they allow to reduce the vibrations on the fairing. DM Code: 001002R003B0
Reference: 001002A02500
Brand: DM
Minibike front fender Dm. New 2024 version in "fiber" composite material. The new DM minibike mudguard is also compatible with previous versions, with 25 and 28 mm fork tubes.
Reference: FM6002-DMT
Brand: Formula
Formula radial rear brake system for minibikes. The Formula mini bike rear brake is the most used for effectiveness and durability, the kit includes the pads. New Formula brake version for minimoto with oversized pump. Formula Code: FM6002-DMT
Conical spacer on the crown side DM, the spacer must be inserted between the swingarm and the wheel bearing with the diameter of the narrowest cone towards the bearing. The wheel spacer Dm has the following measures:
Hole diameter 10 mm
Outside diameter 24 mm
Outside diameter narrow part 15 mm
Spacer thickness 10 mm
Dm code: 001002R002B0
