Xmotorstore Payments
Rear wheel axle for steel swingarm since 2008 DM
Rear wheel axle for steel swingarm since 2008 DM
Reference: KOYO 60002
KOYO racing minimoto wheel bearings 10x26x8, compatible with all minimoto bikes. The high-speed wheel bearings for minimoto allow you to improve the sliding of the minimoto when cornering.
Reference: FRZ.HM3
Brand: CS Racing
Clutch Cs minimoto HAMMER EPIC. Clutch for minimoto compatible with Cs, Iame, Ghr, Bzm engines. This clutch must be used with an 81mm bell. Cs clutch models: - HAMMER GT Low friction coefficient, allows greater slip without affecting performance - HAMMER GP Medium-high friction coefficient - HAMMER EPIC High Coefficient
Reference: GHR 045.001
Brand: GHR
Minimoto bell 80mm M10 Ghr. The 80 mm diameter minimoto bell with M10 pinion thread is compatible with Cs, Ghr, Iame, Bzm bell casings.
Reference: 5013
Brand: STAMAS
Stamas rear hub pulley for water pump drive belt.
Reference: pastiglie-stamas-mecc
Brand: STAMAS
Brake pads for Stamas mechanical caliper.
Reference: 11716
Brand: CS Racing
Keys for shaft Cs Iame Bzm Polini Ghr (5dx 5sx) half moon. The kit consists of: 5 FLYWHEEL SIDE KEYS. 5 CLUTCH SIDE KEYS.
Reference: 7008
Brand: STAMAS
Stamas standard internal rear hub spacer
Reference: PT0.0021
Brand: CS Racing
CS Racing minimoto clutch plate. Dual-mass clutch plate, compatible with CS, Polini, BZM, IAME, TCM clutches, and others. Dedicated clutch plate for Junior A and Junior B single-engine bikes! CIV approved.
Reference: 2016 D25
Brand: STAMAS
Support for factory hydraulic front brake caliper plus screws, for 25 mm diameter forks. The Formula radial stamas caliper support is entirely machined from solid, with CNC machining.
Reference: GHR 020.001
Brand: GHR
Pair of oil seals for minimoto GHR engines. Pair of oil seals for minimoto high smoothness engines GHR, for minimoto engines. The minimoto GHR oil seals are compatible with BZM, CS, IAME, POLINI engines and others. Oil seal measurements: 15x24x5 mm.
Reference: GHR 011.001
Brand: GHR
Ghr cylinder / crankcase stud kit. The kit consists of 9 pieces.
Reference: Pistone IAME 50cc
Brand: CS Racing
Iame Cs piston for 50cc minimoto engines. It is advisable to maintain a tolerance of about 5 hundredths of a millimeter between the cylinder and the piston. The abbreviations R and V indicate the tolerances R = tolerance 0 + 0.01 mm V = tolerance 0 - 0.01 mm
Reference: 112.159.11
Brand: GRC
Rear brake caliper mechanical support for short hub l.111 Grc
Reference: 143.760.004
Brand: POLINI
Semi handlebar with Polini minimoto bracelet. Polini code: 143.760.004 it is possible to use the Polini half handlebar on both the right and left side.
Reference: 112.486.15
Brand: XRACING
Wrench to assemble and disassemble the 6/7/8-tooth minimoto sprocket. Compatible with all minimoto sprockets.
Reference: K2RE-quick-b-charger
Brand: Arianetech
Ariane motorcycle quick battery charger. Fast charger for minibike battery Ariane K2RE, the quick charger allows you to charge the minibike battery quickly (about 15 minutes from 0 to 100%), ideal for use in racing and qualifying.
Reference: 011A
Brand: DM
Support for Gubellini steering damper for minibikes Dm. Support made in cnc, for Dm frame and Fg Gubellini steering damper.
Rear wheel axle for steel swingarm since 2008 DM
