Xmotorstore Payments
Minimoto clutch bell disassembly assembly group. Compatible with all Italian minimoto engines.
Minimoto clutch bell disassembly assembly group. Compatible with all Italian minimoto engines.
Reference: TMC486
Brand: GRC
chain tool minimoto for all minimoto chain. Universal minimoto chain breaker for all minimoto chains. Made in Italy with high quality standards. Compatible with standard and racing pocket chains.
Reference: 112.486.04
Brand: GRC
Clutch locking key for minimoto 2 and 3 masses, Quick coupling. Quick, simple and effective clutch stop wrench to work on the clutch locking it to the crankcase, compatible with Polini, Iame, Cs, Ghr. Code: 112.486.04
Reference: 112.486.20
Brand: GRC
Universal minimoto crankshaft extractor, for Italian engines. Code: 112.486.20
Reference: 112.486.00
Brand: GRC
2-mass clutch unit extractor. Minimoto clutch extractor for all Italian engines. External hole spacing: 34 mm External hole to internal hole center distance: 17.5 mm
Reference: 267000070
Brand: XRACING
Universal flywheel extractor 22x1.5 code: 267000070. This flywheel puller is universal, widely used as a flywheel puller for minimoto. Notes: 22x1.5, right-hand thread.
Reference: 112.486.15
Brand: XRACING
Wrench to assemble and disassemble the 6/7/8-tooth minimoto sprocket. Compatible with all minimoto sprockets.
Reference: Xracing-chiave-frizione
Brand: XRACING
Minibike clutch adjustment wrench. Key to adjust the minibike clutch nuts, compatible with clutches: Polini, Ghr, Bzm, Cs, Iame, and others.
Reference: 143.025.002
Brand: POLINI
Segment diameter 36x1 mm for Polini minimoto 40cc air and h2o. Polini code: 143.025.002
Reference: SCR.0270 + SCR.0287
Brand: CS Racing
CS muffler for flanged motors to be chosen from: Muffler cs flange 10 Muffler cs flange 12 Muffler cs flange 15 (ATTENTION: CYLINDER BUSH EXCLUDED)
Reference: 001002R04800
Brand: DM
Minibike brake wire 100 cm. DM Code: 001002R04800
Reference: FM6006-DMT
Brand: Formula
Formula radial rear brake system for minimoto with upgraded master cylinder and pads included. High performance for racing use.
Reference: 030
Brand: DM
Dm mini bike front fender supports, compatible with 28 mm and 25 mm forks, for plastic fender and carbon fender.
Reference: 001002SP095A
Brand: DM
Pair of dm swingarm register keys dm swingarm keys dm keys dm swingarm keys dm register keys Dm code: 001002SP095A
Reference: X-Filtro
Brand: XRACING
New X-F special racing air filter 100% MADE IN ITALY use: high performance racing universal for: minibike motorbike scooter pitbike brand: Xmotorstore & Marchald Red sponge length: 140mm diameter: 85mm connection diameter: 60/65 mm suitable for venturi. washable X-F was born from the experience gained in years of competitions and from various tests,...
Reference: F00 002 - 029
Brand: DM
Formula rear axial caliper support for Dm. Support for Formula rear brake on Dm minibike. Code: F00 002
Reference: 6017
Brand: STAMAS
Complete Stamas sr r factory fairings kit including mudguards and raw disc protection.
Reference: 143.160.015
Brand: POLINI
Plate for clutch 2 masses reverso engine
Reference: IMH-20450
Brand: CS Racing
Mini bike engine exhaust flange, the flange for air motors is essential to limit the power of the mini bike based on the race category. Flange Measurements: 10mm 12mm 15mm Thickness: 3mm Compatible with: Cs, Iame, Bzm, Polini, Or, Zocchi, Orioli, Tcm.
Reference: IMA-20503
Brand: CS Racing
Iame exhaust gasket for flange 10 12 15. Cs exhaust gasket. ATTENTION: PACK OF 1 PIECE.
Reference: 143.010.011
Brand: POLINI
Cylinder with piston water transfers 3 d.36. Polini code: 143.010.011
Reference: GHR 020.001
Brand: GHR
Pair of oil seals for minimoto GHR engines. Pair of oil seals for minimoto high smoothness engines GHR, for minimoto engines. The minimoto GHR oil seals are compatible with BZM, CS, IAME, POLINI engines and others. Oil seal measurements: 15x24x5 mm.
Reference: 20003.0
Brand: Zocchi
Crown for Chinese mini bike with 3 holes. Zocchi crown for Chinese mini bikes, gold color, with 3 holes. Universal for Chinese minibikes. Minimoto crown measures: Hole spacing: 37 mm (diameter) Hole to hole distance: 32mm Central hole: 26 mm Fixing screw hole: 5 mm
Minimoto clutch bell disassembly assembly group. Compatible with all Italian minimoto engines.
