- On sale!
- New
Xmotorstore Payments
Pair of weights for two-mass clutches GP HAMMER 2.0
New HAMMER 2.0 clutches born from the experience of our technicians directly from the most important competition fields, it has immediately become an irreplaceable tool !!!
Precisely this experience of ours in the world of race minibikes and beyond ... always leads us towards a continuous evolution and improvement of the performance and efficiency of our special parts ...
- gluing system patented by CS RACING on the surface and with two screws to ensure maximum safety and reliability of the friction material, the material is increased by 5%, 4g lightening and new brass bushing to optimize smoothness on the plate pin , ensuring greater efficiency and performance !! is combined with the new CS RACING bell with a diameter of 81, it will have 3 compounds with three different degrees of friction available to meet the needs of all drivers ... from the smallest and lightest to the heaviest ... because everyone knows that the choice of compounds is essential to customize the traction and driveability of your mini bike!
COMPOUNDS:
-HAMMER GT low coefficient of friction, allows greater slippage without affecting performance
-HAMMER GP ... average coefficient of friction
-HAMMER EPIC ... high coefficient of friction
A good choice guarantees to always have excellent performances ... from starts to corner exits always at the top !!
The weights are perfectly compatible with the classic CS plate, they do not require a specific plate !! compatible with all engines on the market
Pair of weights for two-mass clutches GP HAMMER 2.0
New HAMMER 2.0 clutches born from the experience of our technicians directly from the most important competition fields, it has immediately become an irreplaceable tool !!!
Precisely this experience of ours in the world of race minibikes and beyond ... always leads us towards a continuous evolution and improvement of the performance and efficiency of our special parts ...
- gluing system patented by CS RACING on the surface and with two screws to ensure maximum safety and reliability of the friction material, the material is increased by 5%, 4g lightening and new brass bushing to optimize smoothness on the plate pin , ensuring greater efficiency and performance !! is combined with the new CS RACING bell with a diameter of 81, it will have 3 compounds with three different degrees of friction available to meet the needs of all drivers ... from the smallest and lightest to the heaviest ... because everyone knows that the choice of compounds is essential to customize the traction and driveability of your mini bike!
COMPOUNDS:
-HAMMER GT low coefficient of friction, allows greater slippage without affecting performance
-HAMMER GP ... average coefficient of friction
-HAMMER EPIC ... high coefficient of friction
A good choice guarantees to always have excellent performances ... from starts to corner exits always at the top !!
The weights are perfectly compatible with the classic CS plate, they do not require a specific plate !! compatible with all engines on the market
Reference: 112.486.04
Brand: GRC
Clutch locking key for minimoto 2 and 3 masses, Quick coupling. Quick, simple and effective clutch stop wrench to work on the clutch locking it to the crankcase, compatible with Polini, Iame, Cs, Ghr. Code: 112.486.04
Reference: 112.486.25
Brand: GRC
Minimoto clutch bell disassembly assembly group. Compatible with all Italian minimoto engines.
Reference: 112.486.15
Brand: XRACING
Wrench to assemble and disassemble the 6/7/8-tooth minimoto sprocket. Compatible with all minimoto sprockets.
Reference: MAS.HM1
Brand: CS Racing
Pair of weights for GT HAMMER 2.0 two-mass clutches New HAMMER 2.0 clutches born from the experience of our technicians directly from the most important competition fields, it has immediately become an irreplaceable tool !!! Precisely this experience of ours in the world of race minibikes and beyond ... always leads us towards a continuous evolution and...
Reference: CMP.066
Brand: CS Racing
Cs racing minibike bell, universal with M10 pinion thread. Available in size : 81mm 80mm 79mm 78mm
Reference: Xracing-chiave-frizione
Brand: XRACING
Minibike clutch adjustment wrench. Key to adjust the minibike clutch nuts, compatible with clutches: Polini, Ghr, Bzm, Cs, Iame, and others.
Reference: 2005
Brand: STAMAS
Pair of Stamas brake caliper support studs.
Reference: 143.625.001
Brand: POLINI
Polini 910 RS minimoto swingarm. Polini code: 143.625.001 complete left and right swingarm kit for Polini 910 RS and S.
Reference: bzm-79mm-m8
Brand: BZM
Clutch bell Bzm 79 mm M8. Bell for minimoto, self-ventilated, in cast iron, with internal diameter 79 mm and pinion pitch M8.
Reference: 112.173.00
Brand: GRC
Pair of aluminum minimoto levers complete with register
Reference: 112.486.40
Brand: GRC
Muffler springs dismount tool, the spring puller is used to disassemble and assemble the springs from the muffler. Rubberized handle for better grip, curved tip compatible with all springs.
Reference: GHR 015.001
Brand: GHR
Cylinder Ghr 9 pcs reinforced duty kit
Reference: 143.750.002
Brand: POLINI
Polini 910 RS minimoto rear brake caliper. Polini Code: 143.750.002 Rear brake caliper for Polini minibike model 910 RS fairing, compatible with 5-inch and 6.5-inch versions.
Reference: Kit.rev.6,2
Brand: POLINI
Polini 6.2 hp engine overhaul kit. includes: Banco racing c4 bearings. Kit gaskets complete 6.2 hp. Segment 40 or 50cc. Roller cage.
Reference: 001001001000
Brand: DM
Front end kit Dm diameter 28 mm. New Dm d.28 forks, new adjustable fg stroke 50 steering damper, dedicated fairing frame, black anodized 28 diameter aluminum fork with billet aluminum sheaths, CNC front wheel axle anodized billet aluminum fork plates, new black anodized CNC aluminum handlebars with 2-piece anodized billet logo clamps.
Reference: 143.000.026
Brand: POLINI
Minimoto Polini 910 RS 4.2 HP fairing with 5-inch wheels. The Polini 910 4.2 hp minibike is suitable for children aged 4 to 6 years, ideal for taking their first steps on the track, and for taking minibike driving courses, currently the most used minibike in minibike driving lessons. Polini minimoto technical features: Polini engine: 2 T single cylinder -...
Reference: MLL.0043
Brand: CS Racing
Black clutch springs wire 2, 7mm. The black springs are recommended on open engines, they allow a greater starting point.
Reference: 001002A01000
Brand: DM
Screw kit plus rubbers plus spacers for DM minimoto fairing. The DM fairing hardware kit includes 5 grommets, 5 turned bushings, 5 Allen screws, 2 screws. DM Code: 001002A01000
Reference: 074
Brand: DM
Replacement Quick Coupling Front Fairing
Pair of weights for two-mass clutches GP HAMMER 2.0
New HAMMER 2.0 clutches born from the experience of our technicians directly from the most important competition fields, it has immediately become an irreplaceable tool !!!
Precisely this experience of ours in the world of race minibikes and beyond ... always leads us towards a continuous evolution and improvement of the performance and efficiency of our special parts ...
- gluing system patented by CS RACING on the surface and with two screws to ensure maximum safety and reliability of the friction material, the material is increased by 5%, 4g lightening and new brass bushing to optimize smoothness on the plate pin , ensuring greater efficiency and performance !! is combined with the new CS RACING bell with a diameter of 81, it will have 3 compounds with three different degrees of friction available to meet the needs of all drivers ... from the smallest and lightest to the heaviest ... because everyone knows that the choice of compounds is essential to customize the traction and driveability of your mini bike!
COMPOUNDS:
-HAMMER GT low coefficient of friction, allows greater slippage without affecting performance
-HAMMER GP ... average coefficient of friction
-HAMMER EPIC ... high coefficient of friction
A good choice guarantees to always have excellent performances ... from starts to corner exits always at the top !!
The weights are perfectly compatible with the classic CS plate, they do not require a specific plate !! compatible with all engines on the market