Xmotorstore Payments
Malossi Gp mhr exhaust 3213844 replica 4 stroke approved
Code: 3213844
Thanks to the strengthening of Malossi's technical staff (equipped with very modern laboratories) and to the many years of experience in the world of competitions, Malossi wanted to make the difference, giving as an imperative for the design of the new GP MHR REPLICA 4-Stroke mufflers: innovative design, performance, lightness, reliability and QUALITY.
Technical features
European approval
Stainless steel barrel with laser marking, elliptical section
Carbon terminals
Soundproofing system with the addition of mineral fibers with high soundproofing anti-decay power
Complete with DB killers
Exhaust pipes from the cylinder or to the muffler, in stainless steel.
The final assembly of the components using clamps and sealing rivets in stainless steel, gives the exhaust great mechanical resistance and eliminates any dispersion of the exhaust gases.
The GP mhr REPLICA 4-Stroke mufflers are supplied complete with attachments, screws, clamps, gaskets and anything else that may be needed for the relative assembly.
Malossi exhaust for:
3213844 MALOSSI EXHAUST GP MHR REPLICA 4 - STROKE APPROVED YAMAHA MT- 125 IE 4T LC (E3J4E)
3213844 MALOSSI EXHAUST GP MHR REPLICA YAMAHA YZF-R 125 IE 4T LC EURO 3 up to 2013 APPROVED
3213844 MALOSSI GP MHR REPLICA EXHAUST YAMAHA MT- 125 IE 4T LC (E3J4E) APPROVED
Reference: 3213898B
Brand: Malossi
Malossi 3213898B exhaust manifold for Gp Mhr replica Code: 3213898B Malossi exhaust manifold for Gp Mhr homologated replica
Reference: 3214000B
Brand: Malossi
DB Killer Malossi 3214000B Code: 3214000B Db Killer Malossi for Gp Mhr exhaust replica 4 stroke / 4 stroke approved
Reference: 3213897
Brand: Malossi
Malossi titanium silencer for GP MHR REPLICA approved exhaust Malossi code: 3213897
Reference: 3213899b
Brand: Malossi
Malossi connection for GP MHR REPLICA collector approved Malossi code: 3213899b
Reference: 174.2058
Brand: POLINI
Yamaha T Max sintered brake pads Code: 174.2058 Application: Yamaha, Yamaha T Max 500/530 ie / 530, DX, SX ie E4 / 560 Euro 5
Reference: 950.830.031
Brand: POLINI
Hi-Speed e-bike Bosch active line-performance line-cx, code 950.830.031 Hi-Speed e-bike for: Bosch e-bike active line, Bosch performance line, Bosch cx Magnet code 950.870.001
Reference: 01.RP.0015.L
Brand: Ohvale
Ohvale Rear wheel spacer L Code: 01.RP.0015.L
Reference: 242.400
Brand: POLINI
Polini rollers kit 15X12. Available: 242.400 KIT ROLLS 15X12 GR. 2.5-3-3.5-4 242.401 KIT ROLLS 15X12 GR. 3.5-4-4.5-5 242.402 KIT ROLLS 15X12 GR. 4.5-5-5.5-6 242.403 KIT ROLLS 15X12 GR. 5.5-6-6.5-7 242.404 KIT ROLLS 15X12 GR. 6.5-7-8-9
Reference: A4461
Brand: Alfano
Alfano ring with 4 magnets for 50 mm axis. Alfano Code: A4461. Ring with 4 magnets for the speed sensor 50mm. Ring with 4 magnets for axis diameter 50mm for speed sensor A2201. Note: This ring allows for a reaction on the pick up at 4x faster speeds.
Reference: 176.0187
Brand: POLINI
Original Polini rear brake shoe (without spring) d.135X16 mm Code 176.0187 Application: Piaggio, Piaggio Boss, Piaggio Boxer, Piaggio Bravo, Piaggio Cba, Piaggio Ciao, Piaggio Eco, Piaggio Grillo, Piaggio Si, Piaggio Superbravo, Piaggip Trend, Gilera, Gilera Cba This brake shoe for Polini is compatible as an original spare.
Reference: 5319440
Brand: Malossi
Malossi Rhq crankshaft for Piaggio mopeds 5319440 Malossi code: 5319440 Malossi Rhq crankshaft with 10 mm diameter pin and 43 mm stroke 5319440
Reference: 01.SD.0113.L
Brand: Ohvale
Ohvale Gasket tansioner cam chain Code: 01.SD.0113.L
Reference: A2156
Brand: Alfano
Alfano temperature sensor 12 mm A2156. This K thermocouple technology sensor must be installed with a 12mm diameter and 40cm length candle. Caution: It is important to remove the sealing washer from the spark plug before installation. Note: This sensor must be used with an A3401 extension cable or A2190 hub.
Reference: 200.0287
Brand: POLINI
Polini muffler for Piaggio Zip Sp 94cc big evolution (twd). Polini Code: 200.0287. Polini Motori enriches its line of mufflers with the new Polini “BIG EVOLUTION ”developed specifically to make the most of the new series of Big Evolution cylinders for both Piaggio and horizontal Minarelli engines water cooled.
Reference: 140.0058
Brand: POLINI
Polini cylinder kit diameter 57.5 mm. Polini code: 140.0058. Polini cylinder kit for: Paggio, Piaggio Ape 50, Piaggio Ape 50 FL, Piaggio Ape 50 FL2, Piaggio Ape 50 FL3, Piaggio Ape 50 Rst mix, Vespa, Vespa 50 2T Special, Vespa 50 2T PK, Vespa 50 2T XL. Cast iron cylinder
Reference: 02671
Brand: DELLORTO
Dellorto phbg 21 bs carburetor with manual choke knob. Motor mount: 25 Filter connection: M32x1.25 Gas valve: 50 Conical needle: 16 Pulverizer: 262 AU Maximum jet: 96 Minimum jet: 48 Starter jet: 60 Float: 4 gr Dellorto code 02671
Reference: 1111669
Brand: Malossi
Complete Malossi gasket kit for cylinder kit diameter 47 H2O for Kymco Dink, Super 9 Malossi code: 1111669
Reference: 72212PD
Brand: Arrow
Arrow racing stainless steel header for Beta RR 125 4T Enduro and Motard 2024-2025. Not street legal, high performance.
Reference: 280.0019
Brand: POLINI
Polini pin cage 12x15x15 mm Polini pin cage for: Bultaco, Bultaco Astro 50, Bultaco Lobito 50, Derbi, Derbi GPR 50, Derbi Senda 50 DRD R, Derbi Senda 50 Extreme, Derbi Senda 50 R, Gilera, Gilera SMT 50, Gilera RCR 50, Gilera GSM 50 , Gilera H @ K, Gilera ZULU, Polini
Reference: 178.3001
Brand: POLINI
Polini front fork Code: 178.3001 Front fork for: Vespa 125 PK, Vespa 125 Primavera, Vespa 50 Special, Vespa 50, Piaggio Zip 50 2T SP H2O Upper bearing code 178.3502 (for Piaggio Zip and Vespa) Lower bearing code 178.3501 (Piaggio Zip only) Attention: for assembly on Vespa frames, you must use the steering head code 050.2656.
Malossi Gp mhr exhaust 3213844 replica 4 stroke approved
Code: 3213844
Thanks to the strengthening of Malossi's technical staff (equipped with very modern laboratories) and to the many years of experience in the world of competitions, Malossi wanted to make the difference, giving as an imperative for the design of the new GP MHR REPLICA 4-Stroke mufflers: innovative design, performance, lightness, reliability and QUALITY.
Technical features
European approval
Stainless steel barrel with laser marking, elliptical section
Carbon terminals
Soundproofing system with the addition of mineral fibers with high soundproofing anti-decay power
Complete with DB killers
Exhaust pipes from the cylinder or to the muffler, in stainless steel.
The final assembly of the components using clamps and sealing rivets in stainless steel, gives the exhaust great mechanical resistance and eliminates any dispersion of the exhaust gases.
The GP mhr REPLICA 4-Stroke mufflers are supplied complete with attachments, screws, clamps, gaskets and anything else that may be needed for the relative assembly.
